Paieška

Me 7-Segment Serial Display is a classic 4-digit common anode 7-segment display, it usually used to display numbers and a few special characters. You can easily use it in your robot project to show speed, time, the value of sensors, or scores. Me 7-Segment Serial Display is based on chip TM1637, you can control each segment and decimal point individually. Controlling each segment is not a complicated work, we have provided Arduino library for easy programming. Features: 4 digit red alpha-numeric display and one decimal point per digit Selectable brightness, you can see clearly even in daytime 16mm interval M4 mounting holes, compatible with Makeblock beams 2.54mmbreakout pins for connecting with jumper wires Easy wiring with 6P6C RJ25 interface Arduino library for easy programming Specification: Rated Voltage: 5V Digital Bits: 4 Size:24x48x 32mm(Length x Width x Height)

Šis modulis skirtas valdymo plokštei MegaPi. Jis leidžia prijungti RJ25 jungtimis jungiamus elektronikos modulius prie MegaPi smeigtukų. Makeblock RJ25 lizdai yra sužymėti spalvomis, kurios identifikuoja elektronikos modulius ir jų funkcijas: Įrampa: 5V Matmenys: 2.5 x 6.3cm

Megapi Shield is one of MegaPi's pinboards and is one of the electronic modules of mGiraffe. It is mainly used to connect LCD module, position-limit switch/socket, fan module, LED module, and temperature sensor, etc. Every electronic module has corresponding port on the shield, so it is very convenient for you to connect them. Position-limit socket with three directions: X_STOP, Y_STOP, Z_STOP; Lowest position-limit socket: Z_MIN; Two sockets for fan: FAN1 (uncontrollable), FAN2 (controllable); One socket for LED: LED; Two sockets for temperature sensor: TO, T1; Two sockets for LCD: EXP1, EXP2; One socket for serial port expansion: P17; One socket for I2C expansion: P1.

Makeblock Megapi Stepper Motor Driver - elektronikos modulis, skirtas valdyti žingsninius variklius (stepper motor). Maksimali srovė 2,5A. Tinkamas vaėrikliams, dirbantiems pilnu, 1/2, 1/4 1/8 / 1/16 arba 1/32 žingsnio režimu. Techniniai parametrai: Motor driver: DRV8825 Output current：1.75A (with proper heatsinking at 24 V and 25°C） Max current: 2.5A (pay attention to heat dissipation) Drive voltage: 8.2V-45V Note: MegaPi max supply voltage 12V Logic voltage: 5V Dimensions: 1.5 x 2.0cm Compatible with 4 wire bi-polar stepper motors Capable of driving one stepper motor (green interface) Color-code male and female pins ensure connecting with MegaPi correctly A on board heat sink helping heat dissipation

Papildomų konstrukcinių dalių rinkinys mBot robotui. Nuo šiol mBot gali ne tik važiuoti, bet ir vaikščioti! 3-in-1 praplėtimo rinkinys SIX-Legged Robot padės sukonstruoti tris skirtingus mBot roboto variantus: Vabalas Šiašiakojis vabaliukas nepavejamas! Jis greitai juda, greitai sukasi ir žaibiškai atakuoja priešą. Maldininkas Tylus ir romus naktinis medžiotojas. Jis tyliai šliaužia, kantriai sėlina ir bet kada gali tave pagauti! Linksmoji varlytė Linksma išdykusi varlytė šokliuoja taip beprotiškai, kad niekas negali jos sustabdyti.

Makeblock Megapi Encoder/DC Motor Driver gali valdyti du nuolatinės srovės DC variklius. 16 smeigių, kad būtų galima tiesiogiai prijungti prie MegPi valdymo plokštės. Apsauga nuo viršįtampos. Techniniai parametrai: Motor driver: TB6612FNG Motor channels: 2 Minimum operating voltage: 6 V Maximum operating voltage: 12 V Logic voltage: 5 V Continuous output current per channel: 1 A Peak output current per channel: 2 A Dimensions: 1.5 x 3.0 cm

Plokštė turi ATmega2560, kuri turi 54 skaitmenines įėjimo/išėjimo jungtis (iš kurių 14 gali būti panaudotos kaip PWM išėjimai), 16 analoginių išėjimų, 4 UARTai, 16 MHz procesorius, USB jungtis, maitinimo jungtis. Veikimo įtampa 5V.

More resistant to wear and tear, greatly extending the life cycle of the ball screw life increased several times. More high temperatures in harsh environments without distortion to ensure stability. Smoother curve ball ball screw drive designers work more smooth and natural. Packing Included 1 X Rod Lead Screw 1 X Brass Nut

ATMega 32U4 running at 5V/16MHz Supported under IDE v1.0.1 On-Board micro-USB connector for programming 4 x 10-bit ADC pins 12 x Digital I/Os (5 are PWM capable) Rx and Tx Hardware Serial Connections

ATMega 32U4 running at 5V/16MHz Supported under IDE v1.0.1 On-Board micro-USB connector for programming 4 x 10-bit ADC pins 12 x Digital I/Os (5 are PWM capable) Rx and Tx Hardware Serial Connections

This 2.4G Wireless Serial is designed for mBots to be used in classroom or workshop when many people use wireless communication simultaneously. It uses the same the techology as wireless mouse. With the feature of no pairing needed and no drivers needed, there is no signal interference when many modules work simultaneously. With two parts included: a dongle to plug on your computer; a module to plug on the mCore, you can easily establish a wireless connection between the software mBlock and mBot. Features: Allow auto pairing, the same technology as wireless mouse, USB Dongle support 32&64 bit Windows&Mac OS. Driver installed automatically No signal interference when many mBots work simultaneously Specifications: Default Baud rate:115200 Communication distance: about 10 meters Power supply: 5V DC Dimension: 30mm20mm14mm Part list: 2.4G Wireless Serial Module × 1 2.4G Wireless Serial USB × 1