Paieška

Makeblock Me Angular Sensor skirtas aptikti kampo reikšmę. Pagamintas naudojant aukšto tikslumo potenciometrą. Mažas ir lengvai prijungiamas su pridedamais laidais. Me Angular Sensor jungiamas prie RJ25 adapterio arba ZeroPi. Techniniai parametrai: Interface: PH-3P-2.0mm Cable Effective Rotation Angle: 330° Resistance Value: 10K ohms Rotational Life: 1M cycles Input Voltage: 5V Output: Analog Mounting hole: 1 x 4mm Round Hole Product Dimension (LxWxH): 32 x 20 x 7mm

Išsamus elektronikos rinkinys skirtas mokytis grafinio ir Arduino programavimo. Valdymo plokštė sukurta ARDUINO Leonardo pagrindu (ATmega32u4 mikrovaldiklis). Visi jutikliai suderinami su Arduino platforma. Rinkinį sudaro: 1 x Valdymo plokštė MeBaseboard 1 x Me Ultrasonic Sensor 1 x Me Light and Grayscale Sensor 1 x Me Gyro Sensor 1 x Me Temperature Sensor 1 x Me 130 DC Motor 1 x Me RGB LED 1 x Me Joystick 1 x Me RJ25 Adapter 4 x 6P6C RJ25 cable-20cm 2 x 6P6C RJ25 cable-35cm 1 x USB 2.0 A-Male to Micro B-Male Cable 1 x Battery Holder for (6)AA

The Electronic Add-on Pack is to expand on your Starter Robot Kit. There are 8 electronic modules in it. With this add-on pack and Starter Kit, you can create a lot of cool project. You can also implement several projects in Inventor Electronic Kit. Part List: 1 x Me Light Sensor 1 x Me PIR Motion Sensor 1 x Me Temperature Sensor - Waterproof (DS18B20) 1 x Me RGB LED 1 x Me 7-Segment display - Red 1 x Me Joystick 1 x Me Potentionmeter 1 x Me RJ25 Adapter 2 x 6P6C RJ25 cable - 20cm 1 x 6P6C RJ25 cable - 35cm 10 x Socket Cap Screw M4x8 - Button Head 10 x Nut M4 Features: Expand un Makeblock Starter Robot Kit to build more interesting projects. 8 electronic modules included.

Me Slide Potentiometer is one type of potentiometer that can be used to control volume, light intensity, motor speed, movement control, etc. in interactive projects. Features: Compatible with the Arduino sensor expansion board; Three 4mm mounting holes and one RJ25 port for easy assembling; With one red power indicator and one blue potentiometer indicator; Anti-reverse connection protection feature. This Me Slide Potentiometer can be combined with Me Orion (or other Arduino IO/sensor expansion board) in interactive projects. Move the lever from one side to the other, its output voltage will range between 0 V to the VCC you apply. The VCC Me Slide Potentiometer supports vary from 3.3V to 5V.

Me Flame Sensor can be used to detect fire source or light source with wavelength in the range of 760 nm to 1100 nm. Its detection angle is up to 60 degrees, and detection accuracy can be adjusted. When the flame is detected, its blue indicator will light on. It can be applied to the safety monitoring projects such as fire-fighting robot and flame alarm. The port of this module has black ID, and RJ25 cable can used to connect to the port with black ID on Makeblock Orion. Features: The detection distance is 1m when the height of flame is 5cm; The onboard potentiometer can be adjusted for its sensitivity; Anti-reverse protection - connecting the power supply inversely will not damage IC; White area of module is the reference area to contact metal beams; Adopt RJ25 port for easy connection; Provide output ports for digital and analog signal; Provide pin-type of port to support most development boards including Arduino series. Specification: Operating voltage: 5V DC; Spectrum band detected: 840-1200nm; Detection angle: 60°; Feedback time: 15μs; Control mode: digital and analog port; Operating temperature: -25℃~80℃ / -13℉~176℉ (Don’t be too close to the flame to prevent from damage) ; Module dimension: 51 x 24 x 18mm (L x W x H)

Me Gas Sensor includes a smoke sensor of type MQ2 which has good repeatability, long-term stability, short response time, and durable working performance. It is often used as a gas leakage monitoring device in family and factory, and suitable for detecting Liquefied Natural Gas (LNG), butane, propane, methane, alcohol, hydrogen, smoke, etc. Its black ID means that it has an analog port and needs to be connected to the port with black ID on Makeblock Orion. Features: White area of this module is the reference area to contact metal beams; Provide adjustable resistor to adjust sensitivity Preheat for a while before use to keep it warm after preheating; Blue indicator will light on when a certain amount of flammable gas is accumulated and detected; Provide output port for digital and analog signal; Support mBlock GUI programming, and applicable to users of all ages; Adopt RJ25 port for easy connection; Provide pin-type of port to support most development boards including Arduino series. Specification: Operating voltage: 5.0V ± 0.1 V; Heating voltage: 5.0V ± 0.1 V; Heating resistor: 33Ω ± 5% (at room temperature); Heating power: <800mw; Warm up time: >24h; Detection range: 100-10000 ppm; Test temperature: 20 ± 2℃ (at standard condition); Operating temperature: -20℃~50℃ / -4℉~122℉; Relative humidity: < 95%RH; Oxygen concentration: 21% (at standard condition) Module dimension: 51 x 24 x 18mm (L x W x H)

Rinkinyje yra pagrindiniai ir būtiniausi elektronikos moduliai ir komponentai, reikalingi roboto sukūrimui. Valdymo plokštė sukurta ARDUINO Leonardo pagrindu (ATmega32u4 mikrovaldiklis). Plokštėje yra 6 RJ25 lizdai sensoriams ir 2 RJ25 lizdai varikliams. Valdymo plokštė palaiko iki 5V/3A srovę, tai leidžia valdyti aukšto galingumo modulius, pvz. servo variklius ar LED lempučių juostas. Su šiuo rinkiniu galite sukurti IR pulteliu valdomą robotą, liniją sekantį bei kliūčių išvengiantį robotą. Elektronikos modulių prijungimą palengvina RJ25 jungtys, todėl visą laiką ir jėgas galima skirti savo įdėjų įgyvendinimui. Rinkinio dalių sąrašas: 1 x Me-Baseboard 1 x Me-Ultrasonic Sensor 1 x Me-Line Finder 1 x Me-IR Receiver 1 x Me-IR Remote Controller 2 x 6P6C RJ25 cable-20cm 1 x 6P6C RJ25 cable-35cm 1 x USB 2.0 A-Male to Micro B-Male Cable 2 x Base Bracket 1 x Battery Holder for (6)AA 10 x Socket Cap Screw M4x8 4 x Nylon Stud M4*30 10 x Plastic Rivet R4060 4 x Plastic Rivet R4100

This is the temperature sensor based on chip DS18B20 consisting of a waterproof probe and long wire shape, which is perfect for immersive temperature detectionor detectingg something far away.The DS18B20 provides 9 to 12-bit (configurable) temperature readings over a 1-Wire interface, so that only one wire (and ground) needs to be connected from a central microprocessor. The original one includes three wires inside，we adjusted it into a 3-pinconnector so that you can use it simply with Makeblock Me Adapter. (there is no soldering required to connect to our Me BaseBoard just like below picture). Features: Waterproof Uses 1-Wire interface- requires only one digital pin for communication Stainless steel tube 6mm diameter by 35mm long Arduino library for easy programming Dimensions: Probe is 6mm in diameter and roughly 50mm long. Overall length (including wire) is 0.5 meter Specification: Power supply: 3.0V to 5.5V Wide temperature range: -55°C to +125°C High accuracy: ±0.5°C( -10°C to +85°C)